Although the products of the booth manufacturers have entered the mature stage of the market, they are still not mature enough and perfect from the general requirements. They still rely on the natural orientation of the market in terms of technology development and product positioning. The Ministry of Construction of the People's Republic of China set up an automatic door and garage door standardization technical committee in June 2004 to regulate, guide and serve the whole industry. However, it is necessary to meet the requirements of the industry development model in a purely natural state. solved problem:
1. The protection of intellectual property rights is too weak. A group of counterfeit and shoddy manufacturers have just been eliminated, and then there is a batch of unearthed, and there is a tendency for "wild fires to burn out", and the regular-action brand enterprises have to face this unfair competition. In response, it can be said to suffer. Generally speaking, the awareness of the protection of intellectual property rights by Chinese people is not strong in itself. In the actual action, there is no corresponding technical and policy support, which has led to a large number of formal enterprises that have worked hard to invest a lot of money and carefully research and develop new products. Counterfeit and shoddy products flocked to the market and competed with them at a low price. At the same time, the inferior products that were mixed with the fish also made consumers unable to distinguish and were at a loss. This not only causes the enterprises that are officially invested in research and development to suffer losses, but also directly harms the interests of consumers and disrupts the market order.
2. Lack of product standards and technical specifications. Since the self-solding products have only been available for more than ten years, the foundation of technical work has just been established. There is still insufficient technical preparation and sufficient research and data preparation to develop product standards and technical standards. It can be said that the establishment and operation of the Standardization Technical Committee of the Automatic Door Garage Door of the Ministry of Construction has created favorable conditions for the formulation of these standards and technical specifications, but it is necessary for the industry's colleagues to actively participate in the support and cooperation.
3. The long-term development goal of the post-station products is not clear enough. At this stage, most of the manufacturers are fighting each other, crossing the river by feeling the stones, there is no unified and clear identification of what kind of standards to achieve at what time. This will inevitably lead to short-sighted and blind development of the company, not only a waste of resources, but also the best time to miss the development of the industry.
4. Vicious competition. Competition is originally the proper meaning of the market economy, but it is like a double-edged sword. When the market order and the environment are not standardized, if it is used improperly, vicious competition will occur, causing both manufacturers and consumers to suffer. Especially in the case of limited market resources, there are many cases where there are more than a dozen manufacturers to compete in an order. In order for their respective immediate interests, they will eventually evolve into price competition, because it caters to the consumption needs of the Chinese people who are not yet abundant in the current stage of the economy. And low-cost competition will inevitably lead some companies to make a big fuss in reducing manufacturing costs, followed by shoddy raw materials, cut corners, reduced service levels, reduced product quality and quality, and ultimately consumers. Therefore, adhering to the principle of good faith management and respecting the interests of customers is not only the ethical norms that enterprises should abide by, but also the hope of revitalization of the industry.
In the development trend of domestic steel stamping steel processing, manual cutting, semi-automatic cutting machine cutting and CNC cutting machine cutting are used for sheet metal cutting. Manual cutting is flexible and convenient, but the manual cutting quality of the steel processing of the sentry box is poor, the dimensional error is large, the material waste is large, the subsequent processing workload is large, the working conditions are bad, and the production efficiency is low.
The profile cutting machine in the semi-automatic cutting machine has good quality of cutting workpieces. It is not suitable for single piece, small batch and large workpiece cutting due to the use of cutting die for steel processing of its sentry box. Other types of semi-automatic cutting machines, while reducing the labor intensity of workers, are simple in function and are only suitable for cutting parts of more regular shapes.
Compared with the manual and semi-automatic cutting methods, the steel plate processing of the sentry box can effectively improve the cutting efficiency and cutting quality of the plate and reduce the labor intensity of the operator. At present, some small and medium-sized enterprises in China, even in some large enterprises, use hand-cutting and semi-automatic cutting methods for the processing of steel for the booth.